HP Rp5000 - Point of Sale System Troubleshooting Manual Download Page 63

Page: 63 / 78

Troubleshooting Guide

www.hp.com

A–9

POST Error Messages

1201-System Audio
Address Conflict
Detected

Device IRQ address
conflicts with another
device.

Reset the IRQ.

1202-MIDI Port
Address Conflict
Detected

Device IRQ address
conflicts with another
device.

Reset the IRQ.

1203-Game Port
Address Conflict
Detected

Device IRQ address
conflicts with another
device.

Reset the IRQ.

1611-Fan failure
detected

Chassis fan not
connected to the system
board.

1. Reconnect the fan.

2. Replace the fan.

3. Replace the system board.

1720-SMART Hard
Drive Detects
Imminent Failure

Hard drive is about
to fail. (Some hard
drives have a firmware
patch that will fix an
erroneous error
message.)

1. Determine if hard drive is giving

correct error message.

2. Apply firmware patch if applicable.

(Visit

www.hp.com/support

)

3. Back up contents and replace hard

drive.

1721-SMART SCSI
Hard Drive Detects
Imminent Failure

Hard drive is about
to fail. (Some hard
drives have a firmware
patch that will fix an
erroneous error
message.)

1. Determine if hard drive is giving

correct error message.

2. Apply firmware patch if applicable.

3. Back up contents and replace hard

drive.

Numeric Codes and Text Messages

(Continued)

Code/Message

Probable Cause

Recommended Action

Summary of Contents for Rp5000 - Point of Sale System















































































Search results

Summary of Contents for Rp5000 - Point of Sale System

Reviews:

Related manuals for Rp5000 - Point of Sale System

Brands by name

Popular brands

HP Rp5000 - Point of Sale System, Troubleshooting Manual

Search results

Summary of Contents for Rp5000 - Point of Sale System

Reviews:

Related manuals for Rp5000 - Point of Sale System

Brands by name

Popular brands