manualshive.com logo in svg

HP ProLiant DL320e Gen8 v2, User Manual

Share
Download
HP ProLiant DL320e Gen8 v2 User Manual Download Page 77

 

Software and configuration utilities  77 

Keeping the system current 

Access to HP Support Materials 

Access to some updates for HP ProLiant Servers may require product entitlement when accessed through the 

HP Support Center support portal. HP recommends that you have an HP Passport set up with relevant 
entitlements. For more information, see the HP website 

(

http://h20564.www2.hp.com/portal/site/hpsc/public/kb/docDisplay/?docId=c03859703

). 

 

Drivers 

   

 

IMPORTANT:

  Always perform a backup before installing or updating device drivers. 

   

The server includes new hardware that may not have driver support on all OS installation media. 
If you are installing an Intelligent Provisioning-supported OS, use Intelligent Provisioning (on page 

69

) and its 

Configure and Install feature to install the OS and latest supported drivers. 
If you do not use Intelligent Provisioning to install an OS, drivers for some of the new hardware are required. 

These drivers, as well as other option drivers, ROM images, and value-add software can be downloaded as 
part of an SPP. 
If you are installing drivers from SPP, be sure that you are using the latest SPP version that your server 

supports. To verify that your server is using the latest supported version and for more information about SPP, 
see the HP website (

http://www.hp.com/go/spp/download

). 

To locate the drivers for a particular server, go to the HP website (

http://www.hp.com/go/hpsc

) and click 

on 

Drivers, Software & Firmware

. Then, enter your product name in the 

Find an HP product

 field and click 

Go

. 

 

Software and firmware 

Software and firmware should be updated before using the server for the first time, unless any installed 

software or components require an older version.  
For system software and firmware updates, use one of the following sources: 

•

 

Download the SPP ("

HP Service Pack for ProLiant

" on page 

71

) from the HP Service Pack for ProLiant 

download page (

http://www.hp.com/go/spp

). 

•

 

Download individual drivers, firmware, or other systems software components from the server product 
page in the HP Support Center (

http://www.hp.com/go/hpsc

). 

 

Version control 

The VCRM and VCA are web-enabled Insight Management Agents tools that HP SIM uses to schedule 

software update tasks to the entire enterprise. 

•

 

VCRM manages the repository for SPP. Administrators can view the SPP contents or configure VCRM to 

automatically update the repository with internet downloads of the latest software and firmware from 
HP. 

Summary of Contents for ProLiant DL320e Gen8 v2








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands