manualshive.com logo in svg

HP ProLiant DL320e Gen8 v2, User Manual

Share
Download
HP ProLiant DL320e Gen8 v2 User Manual Download Page 12

 

Component identification  12 

Item  LED 

Status 

Definition 

 

 

Off 

Removing the drive does not cause a logical drive to fail. 

4 

Drive status 

Solid green 

The drive is a member of one or more logical drives. 

 

 

Flashing green 

The drive is rebuilding or performing a RAID migration, strip size 
migration, capacity expansion, or logical drive extension, or is 

erasing. 

 

 

Flashing 

amber/green 

The drive is a member of one or more logical drives and predicts 

the drive will fail. 

 

 

Flashing amber  The drive is not configured and predicts the drive will fail. 

 

 

Solid amber 

The drive has failed. 

 

 

Off 

The drive is not configured by a RAID controller. 

 

 

FBWC module LED definitions 

The FBWC module has three single-color LEDs (one amber and two green). The LEDs are duplicated on the 
reverse side of the cache module to facilitate status viewing. 

 

     

1 - Amber 

2 - Green 

3 - Green 

Interpretation 

Off 

Off 

Off 

The cache module is not powered. 

Off 

Flashing 0.5 Hz  Flashing 0.5 Hz  The cache microcontroller is executing from within its 

boot loader and receiving new flash code from the host 
controller. 

Off 

Flashing 1 Hz 

Flashing 1 Hz 

The cache module is powering up, and the capacitor 

pack is charging. 

Off 

Off 

Flashing 1 Hz 

The cache module is idle, and the capacitor pack is 

charging. 

Off 

Off 

On 

The cache module is idle, and the capacitor pack is 
charged. 

Off 

On 

On 

The cache module is idle, the capacitor pack is charged, 
and the cache contains data that has not yet been 
written to the drives. 

Off 

Flashing 1 Hz 

Off 

A backup is in progress. 

Off 

On 

Off 

The current backup is complete with no errors. 

Flashing 1 Hz 

Flashing 1 Hz 

Off 

The current backup failed, and data has been lost. 

Summary of Contents for ProLiant DL320e Gen8 v2








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands