manualshive.com logo in svg

HP ProCurve 8116fl, Installation And Getting Started Manual

Share
Download
HP ProCurve 8116fl Installation And Getting Started Manual Download Page 70

Getting Started With Switch Configuration 

Updating Software 

Get

ting

 S

ta

rte

d W

ith 

S

w

it

ch 

Co

nfi

gurati

o

n 

Updating Software 

The latest software updates for your ProCurve Series 8100fl Switch are 
provided on the ProCurve Networking web site. Updating the system software 
is a four-step process: 

1.   Download the latest software version from the web. 

2.   Verify and compare software versions. 

3.   Install the software image and reboot. 

Refer to the following procedures for details. 

Download the Latest Software.  

To access the latest software for your 

switch, follow the steps below: 

1.   Go to the ProCurve Networking Web site at www.procurve.com. 

2.   From the home page, click on 

Software updates

. 

3.   Under 

Latest software

, click on 

Switches

 to go to the page that has the 

software updates for your switch. 

4.   Click on the software version number that you require, and then follow 

the instructions to download the software. 

Check Software Versions. 

To determine whether you have the latest 

software installed, you can compare the software version that is available on 
the web site with the version that is currently installed on your switch. 

To view the currently installed software version: 

1.   Start a console or telnet session on the switch. 

2.   Enter the 

show version 

command at any level of the CLI: 

Switch 8100fl>show version 

N o t e    

The show version command allows you to display summary version 
information for all installed modules (the default), or you can specify 
parameters to show more detailed information according to the slot 
where individual modules are installed (see the 

Management and 

Configuration Guide

 for further details). 

3-10 

Summary of Contents for ProCurve 8116fl







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands