HP ProCurve 1810G Management And Configuration Manual Download Page 62

Page: 62 / 80

8-4

Link Layer Discovery Protocol (LLPD)

LLDP Remote Device

Use the LLDP Remote Device page to view information about remote devices for which the switch has
received LLDP information. To display the LLDP Remote Device page, click

LLDP > Remote Device

the navigation pane.

As shown in the example configuration in

Figure 8-3

, the remote device is connected to interface 3.

Figure 8-3. LLDP Remote Device Page

Table 8-3. LLDP Remote Device Fields

■

Click the

Refresh

link above the page to re-display the page with current settings from the

switch.

Field

Description

Local Interface

The port on the local system that received the LLDP data from the remote
system.

Chassis ID

The chassis component associated with the remote system.

Port ID

The physical address of the port on the remote device that sent the LLDP data.

Port Description

The port description configured on the remote device. If the port description is not
configured, the field is blank.

System Name

The system description configured on the remote device. If the system
description is not configured, the field is blank.

System Capabilities

The capabilities of on the remote device.

Capabilities Enabled

The capabilities on the remote device that are enabled.

System IP

The IP address of the remote device.

Summary of Contents for ProCurve 1810G

















































































Search results

Summary of Contents for ProCurve 1810G

Reviews:

Related manuals for ProCurve 1810G

Brands by name

Popular brands

HP ProCurve 1810G, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 1810G

Reviews:

Related manuals for ProCurve 1810G

Brands by name

Popular brands