HP ProCurve 1810G Management And Configuration Manual Download Page 54

Page: 54 / 80

7-2

Virtual LAN

VLAN Ports

Table 7-1. VLAN Configuration Fields

■

Click

Apply

to save any changes to the for the currently selected trunk. The changes take effect

immediately. Use the

Maintenance > Save Configuration

page to have the settings remain in effect

after a reboot.

VLAN Ports

Use the VLAN Ports page to view the Port VLAN ID that a port will assign to untagged frames that it
forwards, and to configure the port priority.

To access the VLAN Ports page, click

VLANs > VLAN Ports

in the navigation pane.

Figure 7-2. VLAN Ports Page

Field

Description

Create VLAN

Select this box to create a new VLAN.

Create VLAN ID

Specify the numeric VLAN Identifier from 2 to 4093 and click

Apply

to create the VLAN.

Note

: VLAN ID 1 is pre-configured on the switch and is always named “Default.” The default

VLAN cannot be deleted.

Number of VLANs

The current number of VLANs. Up to 64 VLANs can be created.

VLAN Name
Delete VLAN
Set Name

After the VLAN ID has been created using the previously described fields, you can apply a name
to it or delete it.
• To delete a VLAN, select the

Delete VLAN

box and click

Apply

. The default VLAN cannot be

deleted.

• To specify a VLAN name, select the

Set Name

box, type a name in the VLAN Name field, and

click

Apply

. A VLAN name can have up to 32 alphanumeric characters, including blanks.

Summary of Contents for ProCurve 1810G

















































































Search results

Summary of Contents for ProCurve 1810G

Reviews:

Related manuals for ProCurve 1810G

Brands by name

Popular brands

HP ProCurve 1810G, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 1810G

Reviews:

Related manuals for ProCurve 1810G

Brands by name

Popular brands