HP NJ2000 User Manual Download Page 24 | Manualshive

Page: 24 / 44

background image

3Com Network Jack NJ2000

Page 24 of 44

Copyright © 2009 3Com Corporation. All Rights Reserved.

LACP Status Overview

This page displays the status of the LACP groups.

The LACP Aggregation table has one row for each LACP group. Normal means no LACP group is active. For
active LACP groups, a new row is created from which the status of its port members is displayed. Status of each port
is indicated by a colored box, which use color and number to differentiate status. There are two different tables on
this page:

Aggregation Information

- Information on the Link Aggregation Groups.

LACP Port Status

- Information includes Protocol Active, Partner Port Number, and Operational Port Key

There are two main buttons associated with this page:

HELP

- Displays this window.

REFRESH

- Reloads the current page with the latest configuration settings.

«
...
22
23
24
25
26
...
»

Summary of Contents for NJ2000













































Reviews:

No comments

Related manuals for NJ2000

Brand: Magnetrol Pages: 12

Brand: Magnetrol Pages: 24

Brand: Camozzi Pages: 2

Brand: Lantronix Pages: 2

Brand: ASTEK Pages: 3

Brand: DANLERS Pages: 2

Brand: Cabletron Systems Pages: 194

Brand: Enttec Pages: 22

Digital Energy STS-400-25-3

Brand: GE Pages: 49

UltraHD Switch 3:1

Brand: Oehlbach Pages: 20

CT.TS005.003902

Brand: Talkswitch Pages: 309

Brand: CYP Pages: 20

Brand: PABX Pages: 46

Brand: Manhattan Pages: 4

LMX-1002G-SFP Series

Brand: ANTAIRA Pages: 22

Brand: Harman Pages: 50

Brand: Tabs Pages: 4

Brand: QSFPTEK Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands