HP NJ2000 User Manual Download Page 13 | Manualshive

Page: 13 / 44

background image

3Com Network Jack NJ2000

Page 13 of 44

Copyright © 2009 3Com Corporation. All Rights Reserved.

Upload/Download Configuration

To upload or download the configuration file, select “Upload/Download Configuration”
from the Tools drop-down list, then click “Upload” or “Download,” and then click on the
“Browse” button to select the file.

Restart Switch

To restart the switch, select from the Tools drop-down list, and then click APPLY. The reset will be
complete when the user interface displays the login page.

There are three main buttons associated with this page:

HELP

- Displays this window.

APPLY

- Updates the switch configuration. No changes are made to the configuration until

this button is pressed.

BROWSE

- Navigates to a file.

«
...
11
12
13
14
15
...
»

Summary of Contents for NJ2000













































Reviews:

No comments

Related manuals for NJ2000

DGS-3224TGR - Switch

Brand: D-Link Pages: 160

Brand: D-Link Pages: 145

DGS-1510 Series

Brand: D-Link Pages: 64

DES-3528 - xStack Switch - Stackable

Brand: D-Link Pages: 367

Baseline 2226 Plus

Brand: 3Com Pages: 4

Brand: Cabletron Systems Pages: 52

Brand: SMART Pages: 46

Brand: DAB Pages: 56

Brand: ALFAtron Pages: 15

Brand: AETEK Pages: 2

Brand: SignaMax Pages: 6

Brand: Ruby Tech Pages: 301

Brand: Videosec Pages: 5

Brand: Lantech Pages: 30

Universal Videohub 288

Brand: Blackmagicdesign Pages: 107

TK-407K - KVM Switch - USB

Brand: TRENDnet Pages: 2

Brand: HB Products Pages: 6

Brand: Pakedge Device & Software Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands