HP ML350 - ProLiant - G2 Maintenance And Service Manual Download Page 69

Page: 69 / 78

Component identification 69

Online/activity LED

(green)

Fault/UID LED

(amber/blue)

Interpretation

Flashing regularly

(1 Hz)

Off

Do not remove the drive. Removing a drive may

terminate the current operation and cause data loss.

The drive is rebuilding, or it is part of an array that is undergoing

capacity expansion or stripe migration.

Flashing irregularly Amber, flashing

regularly (1 Hz)

The drive is active, but a predictive failure alert has been

received for this drive. Replace the drive as soon as possible.

Flashing irregularly Off

The drive is active, and it is operating normally.

Off Steadily

amber

A critical fault condition has been identified for this drive, and

the controller has placed it offline. Replace the drive as soon as

possible.

Off

Amber, flashing

regularly (1 Hz)

A predictive failure alert has been received for this drive.

Replace the drive as soon as possible.

Off Off The drive is offline, a spare, or not configured as part of an

array.

Summary of Contents for ML350 - ProLiant - G2















































































Search results

Summary of Contents for ML350 - ProLiant - G2

Reviews:

Related manuals for ML350 - ProLiant - G2

Brands by name

Popular brands

HP ML350 - ProLiant - G2, Maintenance And Service Manual

Search results

Summary of Contents for ML350 - ProLiant - G2

Reviews:

Related manuals for ML350 - ProLiant - G2

Brands by name

Popular brands