HP ML350 - ProLiant - G2 Maintenance And Service Manual Download Page 43 | Manualshive

Page: 43 / 78

background image

Removal and replacement procedures 43

1.

If the processor has separated from the installation tool, carefully re-insert the processor in the tool.

2.

Align the processor installation tool with the socket and install the spare processor.

CAUTION:

The processor is designed to fit one way into the socket. Use the alignment guides on the

processor and socket to properly align the processor with the socket. Refer to the server hood label for

specific instructions.

«
...
41
42
43
44
45
...
»

Summary of Contents for ML350 - ProLiant - G2















































































Reviews:

No comments

Related manuals for ML350 - ProLiant - G2

Brand: Nextech Pages: 7

EXR8STICUSB2321FIS

Brand: StarTech.com Pages: 11

HandyTone-286 Rev 3.0

Brand: Grandstream Networks Pages: 12

WiFi 2.4G RJ45 A

Brand: Epever Pages: 2

Brand: Plantronics Pages: 12

1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps

Brand: Adaptec Pages: 82

Brand: König Pages: 12

Redbooks ServeRAID-3HB

Brand: IBM Pages: 20

Brand: VARIZOOM Pages: 2

Brand: Yealink Pages: 32

Brand: Flying Voice Pages: 46

Brand: Jabra Pages: 2

Brand: Daikin Pages: 20

Brand: Pilz Pages: 29

Brand: Fohhn-Net Pages: 4

Brand: Digitus Pages: 4

Brand: Cochlear Pages: 46

Home MWD 50003 CE

Brand: Somogyi Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands