HP J8697A Installation Manual Download Page 20 | Manualshive

Page: 20 / 56

background image

12

HP Switch zl Modules

FM1 ProCurve J9093A,Fabric Module E8200zl Enabled

FM2 ProCurve J9093A,Fabric Module E8200zl Enabled

Example when standby management the module has rebooted.

ProCurve Switch E8212zl# show redundancy

Settings

--------

Mgmt Redundancy : Enabled

Statistics

----------

Failovers : 3

Last Failover : Tue May 12 17:30:07 2009

Slot Module Description Status SW Version Boot Image

---- ---------------------------------------- --------

MM1 ProCurve J9092A Management Module

E8200zl Standby

K.13.60

Secondary

MM2 ProCurve J9092A Management Module E8200zl Active K.13.60 Secondary

FM1 ProCurve J9093A,Fabric Module E8200zl Enabled

FM2 ProCurve J9093A,Fabric Module E8200zl Enabled

4.

Perform Switchover

E8200zl#

redundancy switchover

This causes a switchover to the management module that received the
new software version, which becomes the active management module.
This method incurs the least amount of network downtime for booting. If
downtime is not an issue, use the

boot system

command. Both management

modules will then be running the new software version.

5.

Both management modules are now updated to new software. If two step
update is required repeat steps 1 through 4 again installing next step
software.

Note:

When a bootROM is updated with software after the boot standby command
is entered the switch will reboot twice, first to update the BootROM to new
version, and then to load the updated system software. Following file copy to
the switch flash and initiation of the boot standby command, no additional
user intervention is needed. Do not interrupt power to the switch during this
important update. See the release notes for additional information.

«
...
18
19
20
21
22
...
»

Summary of Contents for J8697A

























































Reviews:

No comments

Related manuals for J8697A

Brand: B+B SmartWorx Pages: 4

Brand: UfiSpace Pages: 34

Brand: ZoneVu Pages: 15

Brand: Solwise Pages: 231

Brand: ACTi Pages: 14

Brand: Netequalizer Pages: 14

LN1000 - RELEASE NOTES 8-27-2010

Brand: Juniper Pages: 64

ReadyNAS Duo v2

Brand: NETGEAR Pages: 100

Brand: Axtrinet Pages: 49

Brand: Billion Pages: 2

SteelCentral AppResponse 2170

Brand: Riverbed Pages: 166

Brand: Adeunis RF Pages: 9

DGS-1510 Series

Brand: D-Link Pages: 711

Brand: Motorola Pages: 16

Brand: Motorola Pages: 12

HOTZONE DUO 1.0

Brand: Motorola Pages: 28

mT2a - PowerBroadband EthernetXD Switch

Brand: Motorola Pages: 51

WR850G - Wireless Broadband Router

Brand: Motorola Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands