manualshive.com logo in svg

HP J8697A, Installation Manual

Share
Download
HP J8697A Installation Manual Download Page 5

Hewlett-Packard Company

8000 Foothills Boulevard, m/s 5552

Roseville, California  95747-5552

http://www.hp.com/networking/support

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY 
OF ANY KIND WITH REGARD TO THIS MATERIAL, 
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not 
be liable for errors contained herein or for incidental or 
consequential damages in connection with the furnishing, 
performance, or use of this material.

The information contained herein is subject to change 
without notice. The only warranties for HP products and 
services are set forth in the express warranty statements 
accompanying such products and services. Nothing herein 
should be construed as constituting an additional warranty. 
HP shall not be liable for technical or editorial errors or 
omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or 
reliability of its software on equipment that is not furnished 
by Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet on the HP 
Support web site at,

 www.hp.com/networking/support

. A copy 

of the specific warranty terms applicable to your Hewlett-
Packard product and replacement parts can be obtained 
from your HP sales and service office or HP authorized 
reseller.

Summary of Contents for J8697A

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands