manualshive.com logo in svg

HP J8697A, Installation Manual

Share
Download
HP J8697A Installation Manual Download Page 14

6

HP Switch zl Modules

HP 4-Port 10-GbE SFP+ 
zl Module (J9309A)

3

4 ports for connecting 10-GbE 
SFP+ transceivers.

For supported transceivers, visit  

www.hp.com/networking/support

.

– In the first textbox, type 

J4858

 (for 100-Mb and Gigabit information), or 

J8436

 (for 10-Gigabit information).

– Select any of the products that display in the dropdown list.
– Select 

Product support information

.  Then click on 

Manuals

 and find the 

Transceiver Support Matrix

.

For technical details of cabling and technologies see "Cabling and Technology Information" on 

page 36

.

1

 These modules require switch software version K.11.00 or greater and installed on the E5400 zl chassis, or K.12.30 or

   greater to be installed on the E8212 zl chassis.

2

 These modules require switch software version K.11.3x or greater and installed on the E5400 zl chassis, or K.12.30 or

   greater to be installed on the E8212 zl chassis.

3

 These modules require switch software version K.14.34 or greater and installed on the E5400 zl or E8200 zl chassis.

Contact your HP authorized networking products reseller or your HP networking representative for information on 
availability of other modules and mini-GBICs. You can also visit the HP networking products Web site

 

www.hp.com/

networking/support

 

to get more information.

HP Wireless Edge 
Services zl Module 
(J9051A)

4

 

Note

WARNING

There are no ports on the J9051A. 
The module enables the switch to 
operate with HP Radio Ports as a 
centrally-administered Wireless 
LAN system.

For configuration information see 
the Installation and Getting 
Started Guide for your particular 
switch, Chapter 3, “Getting 
Started with Switch 
Configuration”. 

This product contains a Lithium coin-type battery (type CR2032) that requires special handling 
at end-of-life. The battery can explode or cause burns if disassembled, charged, or exposed to 
water, fire or high temperature. After replacing the battery, properly dispose of used battery.

Module

Description

Due to power consumption, no more than four of the 
J9051A or J9052A modules can be installed in a single

chassis.

Summary of Contents for J8697A

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands