HP Elite 7000 Microtower Troubleshooting Manual Download Page 38 | Manualshive

Page: 38 / 49

background image

Solving CD-ROM and DVD Problems

If you encounter CD-ROM or DVD problems, see the common causes and solutions listed in the
following table or to the documentation that came with the optional device.

Table 2-13

Solving CD-ROM and DVD Problems

System will not boot from CD-ROM or DVD drive.

Cause

Solution

The device is attached to a SATA port that has been disabled
in the Computer Setup utility.

Run the Computer Setup utility and ensure

SATA1

Controller

is

Enabled

in the

Advanced

menu.

Non-bootable CD in drive.

Try a bootable CD in the drive.

Boot order not correct.

1.

Run the Computer Setup utility and change the optical
drive boot priority in

Boot

>

Boot Device Priority

>

CD-

ROM Group Boot Priority

.

2.

Run the Computer Setup utility and change boot group
sequence in

Boot

>

Boot Device Priority

.

Drive not found (identified).

Cause

Solution

Cable could be loose.

Check cable connections.

The system may not have automatically recognized a newly
installed device.

See reconfiguration directions in the

Solving Hardware

Installation Problems on page 25

section. If the system still

does not recognize the new device, check to see if the device
is listed within Computer Setup. If it is listed, the probable
cause is a driver problem. If it is not listed, the probable cause
is a hardware problem.

The device is attached to a SATA port that has been disabled
in Computer Setup.

Run the Computer Setup utility and ensure

SATA1

Controller

is

Enabled

in the

Advanced

menu.

CD-ROM or DVD devices are not detected or driver is not loaded.

Cause

Solution

Drive is not connected properly or not properly configured.

See the documentation that came with the optional device.

Movie will not play in the DVD drive.

Cause

Solution

Movie may be regionalized for a different country.

See the documentation that came with the DVD drive.

Decoder software is not installed.

Install decoder software.

Damaged media.

Replace media.

Movie rating locked out by parental lock.

Use DVD software to remove parental lock.

Media installed upside down.

Reinstall media.

32

Chapter 2 Troubleshooting Without Diagnostics

ENWW

«
...
36
37
38
39
40
...
»

Summary of Contents for Elite 7000 Microtower


















































Reviews:

No comments

Related manuals for Elite 7000 Microtower

Brand: VALKPC Pages: 20

DECstation 316+

Brand: DEC Pages: 94

Brand: EUROCOM Pages: 113

ThinkCentre 8105

Brand: IBM Pages: 38

EloPOS 15'' Series

Brand: Elo Touch Solutions Pages: 39

Brand: Büttner Elektronik Pages: 36

Brand: IBM Pages: 72

Brand: LEXIBOOK Pages: 5

TeachWell Mobile Digital WorkSpace

Brand: Ergotron Pages: 6

Brand: Ergotron Pages: 12

TitraLab AT1102

Brand: Hach Pages: 80

Brand: Janz Tec Pages: 20

Brand: Tandy Pages: 171

Brand: UMAX Technologies Pages: 54

Explora 450 Series

Brand: NCD Pages: 62

Brand: Campbell Pages: 47

Brand: Donaldson Torit Pages: 44

Brand: IBM Pages: 240

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands