HP Elite 7000 Microtower Troubleshooting Manual Download Page 19

Page: 19 / 49

Solving Hard Drive Problems

Table 2-3

Solving Hard Drive Problems

Hard drive error occurs.

Cause

Solution

Hard disk has bad sectors or has failed.

In Microsoft Windows XP, right-click

Start

, click

Explore

, and select a drive. Select

File

Properties

Tools

. Under

Error-checking

, click

Check Now

In Microsoft Windows Vista, right-click

Start

, click

Explore

, and right-click on a drive. Select

Properties

then select the

Tools

tab. Under

Error-

checking

click

Check Now

Use a utility to locate and block usage of bad sectors. If
necessary, reformat the hard disk.

Disk transaction problem.

Cause

Solution

Either the directory structure is bad or there is a problem with
a file.

In Microsoft Windows XP, right-click

Start

, click

Explore

, and

select a drive. Select

File

Properties

Tools

. Under

Error-

checking

, click

Check Now

In Microsoft Windows Vista, right-click

Start

, click

Explore

and right-click on a drive. Select

Properties

then select the

Tools

tab. Under

Error-checking

click

Check Now

Drive not found (identified).

Cause

Solution

Cable could be loose.

Check cable connections.

The system may not have automatically recognized a newly
installed device.

See reconfiguration directions in the

Solving Hardware

Installation Problems on page 25

section. If the system still

does not recognize the new device, check to see if the device
is listed within Computer Setup. If it is listed, the probable
cause is a driver problem. If it is not listed, the probable cause
is a hardware problem.

The device is attached to a SATA port that has been disabled
in Computer Setup.

Run the Computer Setup utility and ensure

SATA1

Controller

Enabled

in the

Advanced

menu.

Computer will not boot from hard drive.

Cause

Solution

The device is attached to a SATA port that has been disabled
in Computer Setup.

Run the Computer Setup utility and ensure

SATA1

Controller

Enabled

in the

Advanced

menu.

Boot order is not correct.

Run the Computer Setup utility and change boot sequence in

Boot

Boot Device Priority

Hard drive is damaged.

See the Worldwide Limited Warranty for terms and conditions.

ENWW

Solving Hard Drive Problems

Summary of Contents for Elite 7000 Microtower


















































Search results

Summary of Contents for Elite 7000 Microtower

Reviews:

Related manuals for Elite 7000 Microtower

Brands by name

Popular brands

HP Elite 7000 Microtower, Troubleshooting Manual

Search results

Summary of Contents for Elite 7000 Microtower

Reviews:

Related manuals for Elite 7000 Microtower

Brands by name

Popular brands