HP BCDVideo BCD108 User Manual Download Page 77

Page: 77 / 162

Hardware options installation 77

Install the Smart Storage battery.

Connect the cable.

Install the access panel (on page

Slide the server into the rack.

Connect each power cord to the server.

10.

Connect each power cord to the power source.

11.

Power up the server ("

Powering up the server

" on page

HPE Smart Array P440ar Controller option

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the drives and the

internal system components to cool before touching them.

CAUTION:

To prevent damage to electrical components, properly ground the server before

beginning any installation procedure. Improper grounding can cause ESD.

Summary of Contents for BCDVideo BCD108



































































































































































Search results

Summary of Contents for BCDVideo BCD108

Reviews:

Related manuals for BCDVideo BCD108

Brands by name

Popular brands

HP BCDVideo BCD108, User Manual

Search results

Summary of Contents for BCDVideo BCD108

Reviews:

Related manuals for BCDVideo BCD108

Brands by name

Popular brands