HP BCDVideo BCD108 User Manual Download Page 65

Page: 65 / 162

Hardware options installation 65

Connect the VGA/USB cable to the Front VGA/USB connector toward the rear of the system
board.

4 LFF optical drive connection

Connect the SATA optical cable to the SATA optical/storage drive connector.

Install the access panel (on page

Slide the server into the rack.

10.

Connect all power cords to the server, and then power up the server.

8SFF Universal Media Bay option

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the drives and the

internal system components to cool before touching them.

CAUTION:

To prevent damage to electrical components, properly ground the server before

beginning any installation procedure. Improper grounding can cause ESD.

Summary of Contents for BCDVideo BCD108



































































































































































Search results

Summary of Contents for BCDVideo BCD108

Reviews:

Related manuals for BCDVideo BCD108

Brands by name

Popular brands

HP BCDVideo BCD108, User Manual

Search results

Summary of Contents for BCDVideo BCD108

Reviews:

Related manuals for BCDVideo BCD108

Brands by name

Popular brands