manualshive.com logo in svg

HP A-MSR20, Release Notes, Page: 73 / 88

Share
Download
HP A-MSR20 Release Notes Download Page 73

27 

|     Change The HyperTerminal's Baudrate Accordingly                      | 

|---------------------------<Baudrate Available>---------------------------| 

|<1> 9600(Default)*                                                        | 

|<2> 19200                                                                 | 

|<3> 38400                                                                 | 

|<4> 57600                                                                 | 

|<5> 115200                                                                | 

|<0> Exit                                                                  | 

============================================================================ 

Enter your choice(0-5):5 

The following messages appear: 

Baudrate has been changed to 115200 bps. 

Please change the terminal's baudrate to 115200 bps, press ENTER when ready. 

 

 

NOTE: 

Typically the size of a .bin file is over 10 MB. Even at 115200 bps, the download takes about 30 
minutes.  

 

3.

 

Select Call > Disconnect in the HyperTerminal window to disconnect the terminal from 
the router. 

Figure 2 Disconnect the terminal connection 

 

 

 

NOTE: 

If the baud rate of the console port is 9600 bps, jump to step 

9

. 

 

4.

 

Select File > Properties, and in the Properties dialog box, click Configure. 

Summary of Contents for A-MSR20

























































































Reviews:

No comments