manualshive.com logo in svg

HP A-MSR20, Release Notes

Share
Download
HP A-MSR20 Release Notes Download Page 57

11 

Software features 

Table 13 Software features of A-MSR20_A-MSR30_A-MSR50_A-MSR900_MSR93X Series 

Category 

Features 

LAN protocol: 

ARP (proxy ARP, free ARP, authorization ARP)  
Ethernet_II 
Ethernet_SNAP 
VLAN (PORT-BASED VLAN/MAC-BASED VLAN/VLAN-BASED PORT 
ISOLATE/VLAN VPN/VOICE VLAN)  
802.3x 
LACP(802.3ad) 
802.1p 
802.1Q 
802.1x 
RSTP(802.1w) 
MSTP(802.1s) 
GVRP 
PORT MUTILCAST suppression 

WAN protocols: 

PPP, MP 
PPPoE Client, PPPoE Server 
PPP/MP over FR 
FR, MFR 
FR Fragment, FR Compress, FR over IP 
FRTS 
ATM(IPoA, IPoEoA, PPPoA, PPPoEoA) 
DCC, Dialer Watch 
HDLC 
LAPB 
X25, X25 over TCP, X25 to TCP 
X25 PAD, X25 Huntgroup, X25 CUG 
DLSW(V1.0/2.0) 
ISDN, ISDN Network 
ISDN QSIG 
MODEM 

IP services 

Fast forwarding (unicast/multicast)  
TCP 
UDP 
IP Option 
IP unnumber 
Policy routing  (unicast/multicast) 

Non-IP services: 

SNA/DLSw support 
DLSw Ethernet redundancy backup  
IPX 

Summary of Contents for A-MSR20

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands