HP A-MSR20 Release Notes Download Page 61 | Manualshive

Page: 61 / 88

background image

15

FAX

FAX

Other

Voice RADIUS
VoFR
Analog voice access and emergency

Network
management

SNMP V1/V2c/V3
MIB
SYSLOG
RMON

Local
management

Command line management
File system management
Dual Image

User access
management

Supports console interface login
Supports AUX interface login
Supports TTY interface login
Supports telnet (VTY) login
Supports SSH login
Supports FTP login
Supports X25 PAD login
XMODEM

Appendix B

Upgrading software

This section describes how to upgrade system software while the router is operating
normally or when the router cannot correctly start up.

System software file types

System software images are in .bin format (for example, main.bin) and run at startup. You
can set a system software image as a main, backup, or secure image.
At startup, the router always attempts to boot first with the main system software image. If
the attempt fails, for example, because the image file is corrupted, the router tries to boot
with the backup system software image. If the attempt still fails, the router tries to boot with
the secure system software image. If all attempts fail, the router displays a failure message.

Upgrade methods

You can upgrade system software by using one of the following methods:

Upgrade method

Remarks

Upgrading from the CLI

You  must  reboot  the  router  to  complete  the
upgrade.
This  method  can  interrupt  ongoing  network
services.

«
...
59
60
61
62
63
...
»

Summary of Contents for A-MSR20

























































































Reviews:

No comments

Related manuals for A-MSR20

Brand: Fortinet Pages: 20

Brand: NETGEAR Pages: 14

BladeCenter Management Module

Brand: IBM Pages: 184

Brand: QTech Pages: 406

Brand: ADTRAN Pages: 20

Brand: Raven Pages: 33

Brand: Fluke Pages: 102

Blue Gate ISDN BRI Brave

Brand: Alphatech Pages: 6

Brand: Hama Pages: 45

ExtremeCloud Appliance E3120

Brand: Extreme Networks Pages: 27

Brand: Foscam Pages: 92

Application Module 9109 OCU-DP

Brand: Paradyne Pages: 8

AN5506-04 Series

Brand: FiberHome Pages: 146

Brand: IC Realtime Pages: 131

Brand: Tripp Lite Pages: 2

Brand: Tripp Lite Pages: 2

Brand: Cambium Networks Pages: 172

Brand: Billion Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands