manualshive.com logo in svg

HP A-MSR20, Release Notes

Share
Download
HP A-MSR20 Release Notes Download Page 56

10 

JD577A HP A-MSR 2-port 10/100Base-T FIC Module 
JF824A HP A-MSR 4-port 10/100Base-T FIC Module 
JD604A HP 16-Port 10/100 FIC A-MSR Module 
JD616A HP 16-Port 10/100 POE FIC A-MSR Module 
JD584A HP A-MSR 4-port Enhanced Sync/Async Serial FIC Module 
JD580A HP A-MSR 8-port Enhanced Sync/Async Serial FIC Module 
JD578A HP A-MSR 2-port E1/CE1/PRI FIC Module 
JD588A HP A-MSR 4-port E1/CE1/PRI FIC Module 
JD585A HP A-MSR 8-port E1/CE1/PRI (75ohm) FIC Module 
JD591A HP A-MSR 4-port E1/Fractional E1 FIC Module 
JD592A HP A-MSR 4-port T1/Fractional T1 FIC Module 
JD629A HP A-MSR 1-port T3/CT3/FT3 FIC Module 
JD625A HP A-MSR 1-port E3/CE3/FE3 FIC Module 
JD589A HP A-MSR 4-port Enhanced ISDN-S/T FIC Module 
JD622A HP A-MSR 4-port E1 IMA (75ohm) FIC Module 
JD595A HP A-MSR 1-port T3 ATM FIC Module 
JD596A HP A-MSR 1-port E3 ATM FIC Module 
JD633A HP A-MSR 1-port OC-3c/STM-1c ATM SFP FIC Module 
JD581C HP A-MSR 1-port OC-3c/STM-1c POS FIC Module 
JG201A HP A-MSR 1-port OC-3/STM-1 (E1/T1) CPOS FIC Module 
JD586B HP A-MSR 8-port T1/CT1/PRI FIC Module 
JG200A HP A-MSR 8-port T1 IMA FIC Module 
JF278B HP A-MSR 8-p E1 IMA (75ohm) FIC Module 
Voice interface cards: 
JD602A HP A-MSR 4-port E&M FIC Module 
JD593A HP A-MSR 4-port FXO FIC Module 
JD594A HP A-MSR 4-port FXS FIC Module 
JD605A HP A-MSR 1-port T1 Voice FIC Module 
JD606A HP A-MSR 2-port T1 Voice FIC Module 
JD607A HP A-MSR 1-port E1 Voice FIC Module 
JD587A HP A-MSR 2-port E1 Voice FIC Module 
JG197A HP A-MSR 24-port FXS FIC Module

 

D-FIC 

JD603A HP 24-Port 10/100 DFIC A-MSR Module 
JD617A HP 24-Port 10/100 POE DFIC A-MSR Module 

 

 

CAUTION:  

The support and restriction of modules on A-MSR please refer to HP A-MSR Router Series 
Interface Module Guide, Appendix Purchase Guide

.

 

 

Summary of Contents for A-MSR20

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands