HP 8100 - Elite Convertible Minitower PC Technical Reference Manual Download Page 51

Page: 51 / 112

Technical Reference Guide

www.hp.com

5-1

Input/Output Interfaces

5.1 Introduction

This chapter describes the standard interfaces that provide input and output (I/O) porting of data
and that are controlled through I/O-mapped registers. The following I/O interfaces are covered in
this chapter:

■

SATA/eSATA interfaces (5.2)

■

Serial interfaces (5.3)

■

Parallel interface support (5.4)

■

Keyboard/pointing device interface (5.5)

■

Universal serial bus interface (5.6)

■

Audio subsystem (5.7)

■

Network interface controller (5.8)

Summary of Contents for 8100 - Elite Convertible Minitower PC

















































































































Search results

Summary of Contents for 8100 - Elite Convertible Minitower PC

Reviews:

Related manuals for 8100 - Elite Convertible Minitower PC

Brands by name

Popular brands

HP 8100 - Elite Convertible Minitower PC, Technical Reference Manual

Search results

Summary of Contents for 8100 - Elite Convertible Minitower PC

Reviews:

Related manuals for 8100 - Elite Convertible Minitower PC

Brands by name

Popular brands