manualshive.com logo in svg

HP 8100 - Elite Convertible Minitower PC, Technical Reference Manual, Page: 52 / 112

Share
Download
HP 8100 - Elite Convertible Minitower PC Technical Reference Manual Download Page 52

5-2

www.hp.com

Technical Reference Guide

Input/Output Interfaces

5.2 SATA/eSATA 

Interfaces

These systems provide two, three, or four serial ATA (SATA) interfaces that support tranfer rates 
up to 3.0 Gb/s and RAID data protection functionality. These systems can also support an 
external SATA (eSATA) device through an optional bracket/cable assembly.

5.2.1 SATA interface

The SATA interface duplicates most of the functionality of the EIDE interface through a register 
interface that is equivalent to that of the legacy IDE host adapter. The PCH DO component 
includes Intel RAID migration technology that simplifies the migration from a single hard to a 
RAID0 or RAID1 dual hard drive array without requiring OS reinstallation. Intel Matrix RAID 
provides exceptional storage performance with increased data protection for configurations using 
dual drive arrays. A software solution is included that provides full management and status 
reporting of the RAID array, and the BIOS ROM also supports RAID creation, naming, and 
deletion of RAID arrays.

The standard 7-pin SATA connector is shown in the figure below.  

Figure 5-1.   7-Pin SATA Connector (P60-P63 on system board).

Table 5-1.

7-Pin SATA Connector Pinout

Pin

Description

Pin

Description

1

Ground

6

RX  positive

2

TX positive

7

Ground

3

TX  negative

A

Holding  clip

4

Ground

B

Holding clip

5

RX  negative

--

--

 

Pin 1

Pin 7 

A

B

Summary of Contents for 8100 - Elite Convertible Minitower PC

















































































































Reviews:

No comments