HP 8100 - Elite Convertible Minitower PC Technical Reference Manual Download Page 36 | Manualshive

Page: 36 / 112

background image

4-2

www.hp.com

Technical Reference Guide

System Support

Table 4-1 shows the standard configuration of device numbers and IDSEL connections for
components and slots residing on a PCI 2.3 bus.

NOTES:
[1] Function not used in these systems.
[2] USB 1.1 controllers in 6+6 configuration. 8+4 configuration will have USB 1.1 controller #6 use Function 26, Device 2.
[3] CMT form factor only
[4] Function is only visible in IDE mode (not visible in AHCI orRAID SATA emulation mode).

Table 4-1

PCI Component Configuration Access

PCI Component

Notes

Function #

Device #

PCI Bus

#

IDSEL

Wired to:

Processor:

Host/DMI Bridge
Host/PCI Expr. Bridge
Integrated Graphics Cntlr.
PCI Express x16 (PEG) slot

0
0
0
0

28

1
2
0

0
0
0
1

--

Q57 PCH-D0:

PCI Bridge
LPC Bridge
SATA Controller #1
SMBus Controller
SATA/eSATA Controller #2

Thermal System

USB 1.1 Controller #1
USB 1.1 Controller #2
USB 1.1 Controller #3
USB 1.1 Controller #4

USB 1.1 Controller #5

USB 1.1 Controller #6

USB 2.0 Controller #1
USB 2.0 Controller #2
GbE NIC
Intel HD audio controller
PCIe port 1
PCIe port 2
PCIe port 3
PCIe port 4
PCIe port 5

PCIe port 6

[4]

[1]
[1]
[1]

0
0
2
3
5
6
0
1
2
0
1

3 [2]

7
7
0
0
0
1
2
3
4
5

30

31
31
31
31
31

29
29
29
26
26

29 [2]

29
26
25
27
28
28
28
28
28
28

0
0
0
0
0
0
0
0
0
0
0

0
0
0
0
0
0
0
0
0
0

--

PCI 2.3 slot 1

0

4

7

AD16

PCI 2.3 slot 2

0

11

7

AD17

PCI 2.3 slot 3

[3]

0

10

7

AD18

PCIe x1 slot 1

0

0

32

PCIe x1 slot 2

0

0

48

«
...
34
35
36
37
38
...
»

Summary of Contents for 8100 - Elite Convertible Minitower PC

















































































































Reviews:

No comments

Related manuals for 8100 - Elite Convertible Minitower PC

Brand: Acer Pages: 4

Aspire Z5600 Series

Brand: Acer Pages: 11

Brand: Acer Pages: 17

Brand: Acer Pages: 7

Personal Computer

Brand: IBM Pages: 64

Brand: IBM Pages: 120

Brand: TES Pages: 45

dc5800 - Microtower PC

Brand: Compaq Pages: 69

Brand: Aaeon Pages: 88

IntelliStation POWER 9114 Model 275

Brand: IBM Pages: 92

Brand: Wyse Pages: 114

Brand: VISIONARY DESIGNS Pages: 2

A20-OLINUXINO-MICRO-4GB

Brand: OLIMEX Pages: 57

Brand: Iron Age Office Pages: 7

Brand: MSI Pages: 71

Brand: Korg Pages: 233

VAIO PCV-RX470DS

Brand: Sony Pages: 101

Brand: Toshiba Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands