manualshive.com logo in svg

HP 2/8q Fibre Channel, Installation Manual

Share
Download
HP 2/8q Fibre Channel Installation Manual Download Page 31

Installing

31

HP StorageWorks 2/8q Fibre Channel Switch Installation Guide

d. Remove the locking nut on the rail retaining bracket and move the bracket to the 

farthest position inside the rail. (

Figure 8

)

Figure 8:  Moving the rail retaining bracket on the right rail - rear view

e.

Repeat 

step a

 through 

step d

 for the other rail.

5. Fasten the mounting adapter brackets to the sides of the switch. (

Figure 9)

a.

Place the switch on a stable work surface, and then position the switch and the 
brackets so that the port-side of the switch faces the flanges of the brackets.

b.

Determine which mounting set-back on the brackets to use. The brackets can be 
mounted so that the switch is flush with the rear of the rack, or set back approximately 
three inches.

c.

Use four of the provided screws to attach the brackets to the switch.

Figure 9:  Attaching the mounting adapter brackets to the switch

2

1

Summary of Contents for 2/8q Fibre Channel







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands