HP 2/8q Fibre Channel Installation Manual Download Page 27

Page: 27 / 70

HP StorageWorks 2/8q Fibre Channel Switch Installation Guide

Installing

This section describes how to install and initially configure the 2/8q FC Switch. It also
describes how to backup and update switch firmware.

Topics include:

■

Site requirements

, page 27

■

Installing and initially configuring the switch

, page 28

■

Backing up the switch configuration

, page 37

■

Powering down the switch

, page 37

■

Updating switch firmware

, page 38

Site requirements

Consider factors that affect the climate in your facility, such as equipment heat dissipation and
ventilation. The switch requires the following operating conditions (See

“Specifications

” on

page 59 for a detailed list):

Table 3: Environmental requirements

Item

Requirement

Power requirements

1 Amp at 120 VAC or 0.5 Amp at 240 VAC

Operating temperature range

-40

°C (41°-104°F)

Operating relative humidity

15%-80%, non-condensing

Summary of Contents for 2/8q Fibre Channel







































































Search results

Summary of Contents for 2/8q Fibre Channel

Reviews:

Brands by name

Popular brands

HP 2/8q Fibre Channel, Installation Manual

Search results

Summary of Contents for 2/8q Fibre Channel

Reviews:

Brands by name

Popular brands