manualshive.com logo in svg

HP 16-port SCS, Installation Instructions Manual, Page: 28 / 123

Share
Download
HP 16-port SCS Installation Instructions Manual Download Page 28

 

Operations 22 

 

 
 

Updating the SCS clock 

The SCS supports the network time protocol (NTP) protocol. When NTP is enabled, the battery-backed real-time clock 
on the SCS updates immediately after NTP is enabled, each time the SCS reboots, and, optionally, at specified 
intervals. 

You can specify one or two NTP servers to provide the time. An NTP server can be an external or internal server that 
you supply. The primary server is queried for the time first. If it does not respond with a valid time, the secondary 
server is queried. The second server will be queried for status even if a valid time was obtained from the primary 
server. 

Enabling NTP 

Issue an 

NTP command

 with the 

Enable

 parameter. 

ntp enable [ip=<prim_add> [,<sec_addr>]] [update=<hours>] 

If this is the first time NTP is being enabled, you must specify at least one NTP server address. 

If you want the time to be updated periodically, specify an update interval of up to 99 hours. If you specify a zero 
interval value (which is the default), the time is updated only when the SCS reboots. 

When you enable NTP, you are prompted to confirm or cancel the operation. 

Disabling NTP 

Issue an 

NTP command

 with the 

Disable

 parameter. 

ntp disable 

Configuring serial port settings 

A console target device (TD) can be a serial-managed Linux (or other UNIX) server, router, firewall, or other 
supported serial device. 

By default, SCS ports are configured with the settings listed in Table 3-2. 

Table 3-2 

 Default port settings

 

Parameter Value 

Target device 

Console 

Name 

xx-xx-xx Pn (last three octets of MAC address plus the port number) 

Baud rate 

9600 

Bits per character 

8 

Parity None 

Stop bits 

1 

Flow control 

None 

Time-out 

User Server CLI setting (15 minutes) 

CLI access character 

Use Server CLI setting (^D) 

Power None 

 

Most of these settings are standard serial port operating characteristics. 

The CLI access character parameter specifies how you access the CLI. For more information, see “CLI mode.” 

The 

Power

 parameter instructs the SCS to monitor the state of a specified control signal. Signal transitions can be 

configured to trigger SNMP traps. The parameter value indicates an inbound control signal Clear to Send (CTS), Data 
Carrier Detect (DCD), or Data Set Ready (DSR) and the state of that signal (low or high). When the defined signal is 
true, the SCS interprets it as a power on condition for the attached device. When the signal is false, a power-off 
condition for the device is assumed. The signal specified for flow control cannot be used for power control. 

Summary of Contents for 16-port SCS




























































































































Reviews:

No comments