Hotsy HSS-102589E Operator'S Manual Download Page 20

Hotsy HSS  •   #8.914-412.0   •   Rev. 10/11

21

  

PRESSURE 

W

ASHER

 

  

OPERA

TOR’S MANU

AL
  

MAINTENANCE

Date Oil Changed

Month/Day/Year

No. of Operating Hours

Since Last Oil Change

Brand Name and

Type of Oil (see above)

Maintenance Operation

Every 8 Hrs 

 or Daily

25 Hrs or 

Weekly

50 Hrs or 

Monthly

100 Hrs or 

Yearly

Yearly

Check Oil

Pump

x

Engine

x

Change Oil

Pump

x

Engine

x

Air Cleaner

Check

Clean

Spark Plug

x

Check Valve Clearance

x

Fuel Tank Filter

x

Water Filter/Clean

Check

x

This pressure washer was produced with the best available materials and quality craftsmanship. However, you 
as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative 
maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for 
maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform 
maintenance more often under severe conditions.
Check pump oil level before first use of your new pressure washer. Change pump oil after first 50 hours and 
every 3 months or 500 hours thereafter. Use SAE 30 weight oil, non-detergent.

PREVENTATIVE MAINTENANCE

OIL CHANGE RECORD

Summary of Contents for HSS-102589E























Reviews: