EN
6
WARNING:
before you use the washer-dryer for the first
time, run a wash cycle with detergent and no laundry,
using the 90° cottons cycle without pre-wash.
1.
SWITCH THE MACHINE ON.
Press the button.
All the indicator lights will illuminate for 1 second; the
indicator light corresponding to the button will then
remain lit in a fixed manner and the START/PAUSE
indicator light will flash slowly.
2.
LOAD THE LAUNDRY
.
Open the porthole door.
Load the laundry, making sure you do not exceed the
maximum load value indicated in the table of wash
cycles on the following page.
3.
MEASURE OUT THE DETERGENT.
Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
Description of the machine.
4.
CLOSE THE PORTHOLE DOOR.
5.
SELECT THE PROGRAMME.
Turn the WASH CYCLE
SELECTOR KNOB right or left, until you have selected
the desired wash cycle. A temperature and spin speed is
set for each wash cycle; these may be adjusted.
6.
CUSTOMISE THE WASH CYCLE.
Use the
relevant buttons on the control panel:
Modify the temperature.
The machine automatically displays the maximum
temperature values set for the selected cycle, or the
most recently-used settings if they are compatible
with the selected cycle. The temperature can be
decreased by pressing the
button, until the cold
wash (
) setting is reached. If these buttons are
pressed again, the maximum values are restored.
Exception: if the
Cottons
programme is selected, the
temperature can be increased up to a value of 90°C.
Setting the drying cycle
The first time the button is pressed, the machine
will automatically select the maximum drying cycle
which is compatible with the selected wash cycle.
Subsequent presses will decrease the drying level and
then the drying time, until the cycle is excluded
completely (
). If these buttons are pressed again,
the maximum values are restored.
Drying may be set as follows:
A
- Based on a set time period: between
20
and
180
minutes.
B
- Based on the desired laundry dryness level:
Iron (L1):
suitable for clothes which will need ironing
afterwards. the remaining dampness softens creases,
making them easier to remove.
Hanger (L2):
ideal for clothes which do not need to be
dried fully.
Cupboard (L3):
suitable for laundry which can be put
back in a cupboard without being ironed.
Extra (L4):
suitable for garments which need to be
dried completely, such as sponges and bathrobes.
If your laundry load to be washed and dried is much
greater than the maximum stated load (see adjacent
table), perform the wash cycle, and when the cycle is
complete, divide the garments into groups and put
some of them back in the drum. At this point, follow
the instructions provided for a "
Drying only
" cycle.
Repeat this procedure for the remainder of the load. A
cooling-down period is always added to the end of
each drying cycle.
Drying only
Use the cycle selector knob to select a drying cycle
(
- -
) in accordance with the type of fabric. The
desired drying level or time may also be set using the
DRYING button
.
Set a delayed start.
Press the button until you have reached the desired
delay time. During the setting process, the delay time
is shown on the display and the symbol flashes.
After selecting a delayed start time, the fixed
symbol and the cycle duration will appear on the
display. Press the button once to display the selected
delay time. To remove the delayed start option, press
the button until the display shows the text OFF; the
symbol will disappear.
Once the START/PAUSE button has been pressed,
the time delay may only be decreased.
Modify the cycle settings.
Press the OPTION buttons to customise the wash
cycle in accordance with your own requirements.
Press the button to activate the option; the
corresponding indicator light will switch on.
Press the button again to disable the option; the
indicator light will switch off.
If the selected option is not compatible with the
selected wash cycle, this incompatibility will be
signalled by the flashing of the indicator light and a
sound alert (3 beeps); the option will not be activated.
If the selected option is not compatible with another
option that has been selected previously, the indicator
light corresponding to the first option selected will flash
and only the second option will be activated; the
indicator light corresponding to the button will remain
lit in a constant manner.
7.
START THE PROGRAMME.
Press the START/
PAUSE button. The corresponding indicator light
remains lit in a fixed manner and the porthole door
locks (the
DOOR LOCKED indicator light
illuminates). The icons corresponding to the wash
cycle phases will light up during the cycle to indicate
which phase is currently in progress.
To change a wash cycle once it has already started,
pause the washer-dryer by pressing the START/
PAUSE button; then select the desired cycle and
press the START/PAUSE button again. To open the
door during a wash cycle, press the START/PAUSE
button; if the DOOR LOCKED
indicator light is
switched off you may open the door. Press the
START/PAUSE button again to restart the wash cycle
from the point at which it was interrupted.
8.
THE END OF THE WASH CYCLE.
This is indicated
by the illuminated text
END
. The porthole door may be
opened immediately. If the START/PAUSE indicator light
is flashing, press the button to end the cycle. Open the
door, unload the laundry and switch off the machine.
If you wish to cancel a cycle which has already begun,
press and hold the button until the cycle stops and
the machine switches off.
How to run a wash cycle or a
drying cycle
