Hoshizaki TempGuard FH1-SSB Service Manual Download Page 5

Page: 5 / 63

I. Specifications

A. Nameplate Ratings

Design Pressure (PSIG) Refrigerant

AC Supply Voltage

Amperes

R-404A

RH1-SSB / RH1-SSB-HD

115/60/1

7.0

450

1. OZ

RH1-SSB-GD

115/60/1

10.7

450

16.1 OZ

FH1-SSB / FH1-SSB-HD

115/60/1

1.0

450

15. OZ

RH-SSB / RH-SSB-HD

115/60/1

10.0

450

18. OZ

RH-SSB-GD

115/60/1

11.8

400

1.5 OZ

FH-SSB / FH-SSB-HD

115/60/1

15.5

450

0.1 OZ

RH3-SSB / RH3-SSB-HD

115/60/1

13.0

450

3. OZ

RH3-SSB-GD

115/60/1

15.5

450

31.4 OZ

RIR-SSB51-0

115/60/1

11.0

450

18. OZ

PTR1SSB-xxxx / PTR1-SSB01-10

115/60/1

1.0

450

15.5 OZ

Design Pressure (PSIG)

Refrigerant

AC Supply

Voltage

Amperes

Refrigerator

Freezer

R-404A

Refrigerator

Freezer

RFH-SSB / RFH-SSB-HD

115/60/1

450

1. OZ

15. OZ

RFH3-SSB / RFH3-SSB-HD

115/60/1

450

18. OZ

15. OZ

RFH1-SSB-HD

115/60/1

16.0

450

9.5 OZ

1.0 OZ

See the nameplate for electrical and refrigeration specifications. The nameplate is located
on the right side wall of the cabinet interior.

Note: We reserve the right to make changes in specifications and design without prior

notice.

Summary of Contents for TempGuard FH1-SSB
































































Search results

Summary of Contents for TempGuard FH1-SSB

Reviews:

Hoshizaki TempGuard FH1-SSB, Service Manual, Page: 5 / 63

Search results

Summary of Contents for TempGuard FH1-SSB

Reviews: