manualshive.com logo in svg

Hoshizaki TempGuard FH1-SSB, Service Manual, Page: 13 / 63

Share
Download
Hoshizaki TempGuard FH1-SSB Service Manual Download Page 13

13

Note: The start circuit of the compressor is timed such that at power-up and during 

any compressor off time, there will be at least a  1/ minute delay before the 
compressor will start. The only exception is when the overload activates and 
deactivates. The compressor has a  1/ minute minimum run time during every 
run cycle.  

2. Freezer (except freezer side of RFH1-SSB-HD) auxiliary code P5 and earlier

a) Sequence of Operation

Cycle On 

(Cut-on 

temperature reached) 
[Minimum .5 minutes]
1. Compressor on
. Condenser on
3. Evaporator on

 

2.5 minute delay

1. Compressor start-up
. Condenser fan start-up
3. Evaporator fan start-up

POWER ON

Board Self Check

Display reads "r_##"
(## is board revision)
Frame heaters on

Cycle Off 

(Cut-out 

temperature reached) 
[Minimum .5 minutes]
1. Compressor off
. Condenser fan off
3. Evaporator fan off

Defrost Start

Preprogrammed time interval
1. Compressor off
. Evaporator fan off
3. Condenser fan off
4. Defrost heater on
5. "dEF" displayed

Defrost End

Defrost thermistor 
reaches 100°F;
Defrost heater off

Five minutes after 
defrost heater off
1. Compressor on
. Condenser fan on

Evaporator temperature 
reaches below 70°F 
1. Evaporator fan on

Cabinet temperature reads 
a value below 15°F above 
the setpoint.
"dEF" no longer displayed, 
cabinet temp. displayed.

Normal cycling continues

Summary of Contents for TempGuard FH1-SSB
































































Reviews:

No comments