manualshive.com logo in svg

Hoshizaki TempGuard FH1-SSB, Service Manual, Page: 2 / 63

Share
Download
Hoshizaki TempGuard FH1-SSB Service Manual Download Page 2

IMPORTANT

Only qualified service technicians should attempt to service or maintain this 
unit. No such service or maintenance should be undertaken until the technician 
has thoroughly read this Service Manual. 

HOSHIZAKI provides this manual primarily to assist qualified service technicians in the 
service and maintenance of the unit. 

Should the reader have any questions or concerns which have not been satisfactorily 
addressed, please call, write or send an e-mail message to the HOSHIZAKI Technical 
Support Department for assistance.

HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City, GA 3069

Attn: HOSHIZAKI Technical Support Department

Phone: 1-800-33-1940 Technical Service
 

  (770) 487-331

Fax:    1-800-843-1056
 

  (770) 487-3360

E-mail: [email protected]

Web Site: www.hoshizaki.com

NOTE: To expedite assistance, all correspondence/communication MUST include the    

  following information:

   

 

• Model Number

   

 

• Serial Number

   

 

• Complete and detailed explanation of the problem   

Summary of Contents for TempGuard FH1-SSB
































































Reviews:

No comments