Hoshizaki Serenity Series KMS-822MLH Service Manual Download Page 7

Page: 7 / 47

I. Specifications

A. Icemaker

1. KMS-822MLH

Note: We reserve the right to make changes in specifications and design without prior

notice.

AC SUPPLY VOLTAGE

115VAC Supplied by SRK-10H via Factory Supplied

Wire Harness

APPROXIMATE ICE PRODUCTION

Ambient

WATER TEMP. (°F)

PER 24 HR.

Temp.(°F)

lbs./day ( kg/day )

*839 (381)

820 (372)

769 (349)

Reference without *marks

824 (374)

795 (361)

730 (331)

820 (372)

*774 (351)

714 (324)

100

801 (364)

760 (345)

659 (299)

SHAPE OF ICE

Crescent Cube

ICE PRODUCTION PER CYCLE

13.6 lb. (6.2 kg) 624 pcs.

ELECTRIC & WATER CONSUMPTION

90/70°F

70/50°F

KMS/SRK COMBINED ELECTRIC W (kWH/100 lbs.)

1800 (5.58)

1710 (4.89)

WATER gal./24HR (gal./100 lbs.)

149 (19.3)

363 (43.3)

EXTERIOR DIMENSIONS (W×D×H)

22"×24-5/8"×28" (559×625×713 mm)

EXTERIOR FINISH

Stainless Steel, Galvanized Steel (rear)

WEIGHT

Net 122 lb. (55 kg), Shipping 152 lb. (69 kg)

CONNECTIONS - ELECTRIC

Wire Harness Connection from SRK to KMS

- WATER SUPPLY

Inlet

1/2" FPT

- DRAIN

Outlet

3/4" FPT

- CONDENSATION

5/8" OD Tube

- REFRIGERATION

Liquid Line

1/2" Copper Tube Field Connection

Suction Line

5/8" Copper Tube Field Connection

CUBE CONTROL SYSTEM

Float Switch

HARVEST CONTROL SYSTEM

Hot Gas and Water, Thermistor and Timer

ICE MAKING WATER CONTROL

Timer Controlled, Overflow Pipe, Float Switch

COOLING WATER CONTROL

N/A

BIN CONTROL SYSTEM

Mechanical Bin Control

COMPRESSOR

In SRK

CONDENSING UNIT

Air-Cooled Remote Condensing Unit SRK-10H

EVAPORATOR

Vertical type, Stainless Steel and Copper

REFRIGERANT CONTROL

Thermostatic Expansion Valve

Headmaster (C.P.R.) in SRK-10H (160 PSI)

REFRIGERANT CHARGE

404A, 14 lb. 15.9 oz. (6800 g)

(Icemaker 0 lb. 7.1 oz. (200 g))

(Cond. Unit 14 lb. 8.8 oz. (6600 g))

DESIGN PRESSURE

High 467 PSIG, Low 230 PSIG

CONTROL BOARD CIRCUIT PROTECTION

High Voltage Cut-out (Internal)

REFRIGERATION CIRCUIT PROTECTION

Auto-Reset High Pressure Switch in SRK-10H

LOW WATER PROTECTION

Float Switch

ACCESSORIES -SUPPLIED

Mechanical Bin Control Extension Bracket

-REQUIRED

Dispenser Unit or Ice Storage Bin

SRK-10H Remote Condensing Unit

OPERATING CONDITIONS

VOLTAGE RANGE

104-127VAC

AMBIENT TEMP.

45 -100°F

WATER SUPPLY TEMP.

45 - 90°F

WATER SUPPLY PRESSURE

10 - 113 PSIG

ENG.F-011.1.0205

Summary of Contents for Serenity Series KMS-822MLH
















































Search results

Summary of Contents for Serenity Series KMS-822MLH

Reviews:

Hoshizaki Serenity Series KMS-822MLH, Service Manual, Page: 7 / 47

Search results

Summary of Contents for Serenity Series KMS-822MLH

Reviews: