horsch 420016020001 Owner'S Manual Download Page 73

Page: 73 / 84

Omnis FT Owner’s Manual – Ver. 2.0 06/2020

www.horsch.com

SCH

Preparation for Storage

If you want to store the machine for a longer period, pay attention to the following points:

•

Park the machine inside a building if possible.

•

Remove any soil/dirt buildup on the machine.

•

Protect the machine against rust. If you want to spray the tillage machine with oil, use only oils

that are easily biodegradable, e.g., rapeseed oil.

Removing from Storage

1. Check tire air pressure and inflate, as necessary.

2. Clean the machine thoroughly.

3. Perform required lubrication. See Lubrication and Maintenance in this section.

4. Check all hardware and torque bolts as needed.

5. Review Owner’s Manual, giving special attention to safety precautions.

Summary of Contents for 420016020001





















































































Search results

Summary of Contents for 420016020001

Reviews:

Related manuals for 420016020001

Brands by name

Popular brands

horsch 420016020001, Owner'S Manual

Search results

Summary of Contents for 420016020001

Reviews:

Related manuals for 420016020001

Brands by name

Popular brands