EN
4
Cirrus SR22T 1.5m
Transmitter Setup
WARNING
: If your transmitter allows it, enable the throttle cut feature.
Always engage throttle cut before approaching the aircraft.
WARNING
: Never assign Aux 2 to SAFE Select during transmitter setup
with any model transmitter. If SAFE Select is assigned to Aux 2, the
throttle channel/motor will reverse in flight once SAFE is enabled. Motor
reversing is assigned to Aux 2/channel 7 by default in the Smart ESC.
IMPORTANT:
After you set up your model, always rebind the transmitter and
receiver to set the desired failsafe positions.
IMPORTANT:
The included receiver has been programmed specifically for
operation in this aircraft.
†
Some of the terminology and function locations used in the iX12 and iX20
programming may be slightly different than other Spektrum AirWare™ radios.
The names given in parentheses correspond to the iX12 and iX20 programming
terminology. Consult your transmitter manual for specific information about
programming your transmitter.
Pre-Programmed Transmitter Setup Files
To save time when setting up your transmitter for this model, visit www.
SpektrumRC.com to download the latest pre-programmed transmitter setup files.
The files are found under “SETUPS/UPDATES” and the “AIR TRANSMITTER SETUPS”
link. Select your radio/transmitter, then on the corresponding page under “SETUPS
& DOWNLOADS” click the “DOWNLOAD SETUPS” button to view the available
files in the drop down list. Locate the file for this model using the item number.
Download the correct model file to and install it in your transmitter using an SD
card.
Dual Rates
Low rate is recommended for the initial flights.
NOTICE:
To ensure AS3X
®
technology functions properly, do not lower rate
values below 50%. If lower rates are desired, manually adjust the position of the
pushrods on the servo arm.
NOTICE:
If oscillation occurs at high speed, refer to the Troubleshooting Guide
for more information.
Exponential
After first flights, you may adjust expo in your transmitter.
Thrust Reversing
Motor reversing is not enabled when this aircraft is new. See the
Thrust Reversing
section of this manual for information about setting up and using the motor
reversing function in the ESC.
Transmitter Telemetry Setup
If the transmitter that you intend to use with this aircraft is not displaying
telemetry data, visit www.SpektrumRC.com and update your firmware. With the
latest firmware installed on your transmitter the telemetry option should now be
functional on your transmitter.
For first flight, set flight timer for 4 minutes. Adjust timer thereafter depending on
battery used and flying style.
DX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to
System Setup
and
click the scroll wheel. Choose yes.
2. Go to
Model Select
and choose
<Add New Model>
at the bottom of the list.
The system asks if you want to create a new model, select
Create
3. Set
Model Type
: Select
Airplane Model Type
by choosing the airplane.
The system asks you to confirm model type, data will be reset. Select
YES
4. Set
Model Name
: Input a name for your model file
5. Select
<Main Screen>,
Click the scroll wheel to enter the
Function List
6. Set
D/R (Dual Rate) and Expo
;
Aileron
Set
Switch
:
Switch F
Set
High Rates:
100%
,
-
Low Rates:
70%
iX Series Transmitter Setup
1. Power ON your transmitter and begin once the Spektrtum Airware app is open.
Select the orange pen icon in the upper left corner of the screen, the system
asks for permission to
Turn Off RF
, select
PROCEED
2. Select the three dots in the upper right corner of the screen,
select
Add a New Model
3. Select Model Option, choose
DEFAULT
, select
Airplane.
The system asks if you want to create a new acro model, select
Create
4. Select the last model on the list, named
Acro
.
Tap on the word Acro and rename the file to a name of your choice
5. Tap and hold the back arrow icon in the upper left corner of the screen to
return to the main screen
6. Go to the
Model Setup
tab
7. Exit
Model Setup
, Go to the
Model Adjust
menu
8. Set
Dual Rates and Expo
; Select
Aileron
Set
Switch
:
Switch F
Set
High Rates:
100%
, Expo
10%
-
Low Rates:
70%
, Expo
5%
9. Set
Dual Rates and Expo
; Select
Elevator
Set
Switch
:
SWITCH C
High Rates
:
100%,
Expo
10%
-
Low Rates
70%,
Expo
5%
10. Set
Dual Rates and Expo
; Select
Rudder
Set
Switch
:
SWITCH G
High Rates
:
100%,
Expo
10%
-
Low Rates
70%,
Expo
5%
11. Set
FLAP SYSTEM
;
SWITCH D,
NORM:
-100%, MID: 0% with 6% Elevator,
LAND: 100% with 10% Elevator, SPEED 2.0S
12. Set
Throttle Cut
;
Switch
:
Switch H,
Position:
-100%
NX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to
System Setup
and
click the scroll wheel. Choose yes.
2. Go to
Model Select
and choose
<Add New Model>
near the bottom of the
list. Select
Airplane Model Type
by choosing the airplane, select
Create
3. Set
Model Name
: Input a name for your model file
4. Select
<Main Screen>,
Click the scroll wheel to enter the
Function List
5. Set
D/R (Dual Rate) and Expo
;
Aileron
Set
Switch
:
Switch F
Set
High Rates:
100%
, Expo
10%
-
Low Rates:
70%
, Expo
5%
6. Set
D/R (Dual Rate) and Expo
;
Elevator
Set
Switch
:
SWITCH C
High Rates
:
100%,
Expo
10%
-
Low Rates
70%,
Expo
5%
7. Set
D/R (Dual Rate) and Expo
;
Rudder
Set
Switch
:
SWITCH G
High Rates
:
100%,
Expo
10%
-
Low Rates
70%,
Expo
5%
8. Set
FLAP SYSTEM
;
SWITCH D,
NORM:
-100%, MID: 0% with 6% Elevator,
LAND: 100% with 10% Elevator, SPEED 2.0S
9. Set
Throttle Cut
;
Switch
:
Switch H,
Position:
-100%
DX Series Transmitter Setup
7. Set
D/R (Dual Rate) and Expo
;
Elevator
Set
Switch
:
SWITCH C
High Rates
:
100%,
-
Low Rates
70%
8. Set
D/R (Dual Rate) and Expo
;
Rudder
Set
Switch
:
SWITCH G
High Rates
:
100%
-
Low Rates
70%
9. Set
FLAP SYSTEM
;
SWITCH D,
NORM:
-100%, MID: 0% with 6% Elevator,
LAND: 100% with 10% Elevator, SPEED 2.0S
10. Set
Throttle Cut
;
Switch
:
Switch H,
Position:
-100%
