manualshive.com logo in svg

Horizon Fitness SPF-10II, Manual

Share
Download
Horizon Fitness SPF-10II Manual Download Page 48

44

6. Installation Instruction

A. CCR(DX)(Criss-Cross Receiving Tray)

(1) Install connector CNC at the delivery end

of SPF-10II with hooks of CNC inserted in
keyhole of SPF-10II.

(2) Connect connector cable of CNC to the

receptacle of SPF-10II.

(3) Install CCR (DX) at the delivery end of

SPF-10II and connect connector of
CCR(DX) to receptacle of SPF-10II.

B. ST-20 (Stacker Type Receiving Tray)

(1) Install connector CNS at the delivery end

of SPF-10II with hooks of CNS inserted in
keyhole of SPF-10II.

(2) Connect connector cable of CNS to recep-

tacle of SPF-10II.

(3) Install ST-20 at the delivery end of SPF-

10II with 3 mm clearance provided be-
tween moveable guide of receiving tray
and the edge of sheets delivered.

(4) Connect connector of receiving tray to

receptacle of SPF-10II.

NOTE
Optional forked connector is required when
ST-20 is installed with SPF-10II.

6-1 Installation Instruction

6-1-3 Receiving Tray Installation

CNC

CCR(DX)

CNS

ST-20/STR

Summary of Contents for SPF-10II



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands