manualshive.com logo in svg

Horizon Fitness SPF-10II, Manual

Share
Download
Horizon Fitness SPF-10II Manual Download Page 45

41

6. Installation Instruction

6-1 Installation Instructions

6-1-2 Connection of SPF-10II with Collator

When selecting a site to install SPF-10II and
collator, pay due attention to the following
points.

(1) Select a flat strong floor free from vibra-

tion.

(2) Select a place free from direct exposure to

sunlight.

(3) Select a place free from extremely high

temperature and humidity.

(4) Install connecting unit onto the SPF-10II.

CNP.......... AC-Friction

HAC-Series
MC-Series

CNA.......... AC-8000S
CNM..........MAC-Series

(5) Connect connector of CNA to receptacle of

SPF-10II.

(6) Connect SPF-10II with collator by install-

ing a connecting plate between SPF-10II
and collator.

COLLATOR

SPF-10II

Leveling Bolt
& Locking Nut

Locking
Bolt

Connecting
 Plate

Ground

From Collator

From Connector
CNA, CNP or CNM

From Trimmer,
Criss-cross or
Stacker Receiving
Tray

From Conveyor,
Connector CNC.
or CNS

Connector CNA,
CNP, CNM

Air Hose

Connecting Plate

Positioning Pin

Rubber

Connector to
Receptacle of
Collator

Summary of Contents for SPF-10II



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands