background image

 

Adjustment for carpet

pile height

The cleaning of carpet and rugs
takes place at the nozzle. This is
the opening at the bottom of the

cleaner where the agitator is lo-
cated.

It is necessary for the nozzle to be

adjusted properly to the various
carpet pile heights. The adjust-
ment lever on the front of the
cleaner may be set on three differ-
ent self-adjusting ranges.

On very dense pile plush or shag
carpet, some difficulty in pushing

the cleaner may occur. In this

case, position the adjustment le-

ver on PLUSH or SHAG.

When cleaning 
floors, set adjustment lever to

LOW/MEDIUM and use LOW
SPEED, if available on your

cleaner. Because of the vigorous
action of the agitator, 

do not

allow cleaner to run in a sta-
tionary position 

on any floor

covering, as marring may occur.

Disconnect cleaner from electri-

cal outlet before making nozzle
adjustment.

To change nozzle adjustment
grasp the handle and tilt the

cleaner forward. Move the lever

with your hand until it “clicks” in-
to the desired position.

Air freshener

dispenser

 

 

Lift the drawer in the bag cap of

your cleaner and insert the air

freshener tablet that has been

packed with your cleaner. Push

drawer down into position.

7

NOZZLE

Summary of Contents for Concept one
























Reviews: