background image

 

The bag

Your cleaner has a durable outer bag which covers the throw away bag.
A light wiping with a damp cloth will keep this outer bag clean.

When to replace the throw away bag

Check the bag from time to time. It is recommended that you change the
bag when the dirt reaches the dotted line on the throw away bag. If you
let more dirt than this accumulate, your cleaner may not operate effec-

tively. Change bag frequently when using cleaner on new carpet, due to

rapid accumulation of carpet fluff. Also check dirt duct (see section fol-
lowing belt replacement) for fluff accumulation.

Where to buy bags

Bags may be purchased from your local Authorized Hoover Dealer or

from a Hoover Factory Service Center. 

When ordering bags, be sure to

give the model number of your cleaner.

What bags to buy

Use HOOVER bag 

type A 

with this cleaner.

To assure that your HOOVER cleaner operates at peak per-
formance, it is imperative that you use only genuine

HOOVER throw away bags made by The Hoover Company.
HOOVER bags can be identified by the trademarks   

How to change bag

Disconnect cleaner from elec-

trical outlet.

1. To remove old bag, put fingers

behind bag collar, pull off and re-
move.

Dispose of old bag.

Do not try to clean out used bag.
Cleaner will not operate 

12

Summary of Contents for Concept one
























Reviews: