Hood Depot KAP Series Installation, Operation And Maintenance Manual Download Page 3

Page: 3 / 17

Commercial Kitchen Ventilation Products

710 S. Powerline Road, Deerfield Beach, FL 33442 • 954 570-4083 • 800 322-8730 • www.hooddepot.net

DESCRIPTION

The listed air purification unit is suitable for the removal of smoke, grease laden

vapors and odors in commercial cooking installations. Hood Depot KAP purification

units are specified in CFM ratings from 5,000 to 40,000 CFM to handle all size kitch

ens with any cooking equipment configuration. Grease ducts must still conform to

NFPA 96 and your local mechanical codes applicable to gauges, sizing and clean-

out requirements.

If a grease fire has occurred, the system should be dismantled and inspected by a

professional engineer. Hood Depot International™ cannot be held responsible for

grease duct systems that are not properly maintained or have been subjected to a

grease fire.

COMMON INSTALLATION FORMATS

Interior Split Fan & Filter

Interior Horizontal Suspension

Exterior Roof Mounted

Pg. 3

Interior Floor Mounted

KAP

Summary of Contents for KAP Series


















Search results

Summary of Contents for KAP Series

Reviews:

Related manuals for KAP Series

Brands by name

Popular brands

Hood Depot KAP Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for KAP Series

Reviews:

Related manuals for KAP Series

Brands by name

Popular brands