Hood Depot KAP Series Installation, Operation And Maintenance Manual Download Page 17

Page: 17 / 17

Issue Date: Expires: Authorized by:

One Year Limited Warranty

Hood Depot™ warrants this Kitchen Air Purifier against defects of material and workman-

ship for a period of one year from date of installation contingent upon proper maintenance

as described in the KAP Series Air Purification Unit “Installation, Operation and Mainte-

nance Manual”. Hood Depot will not be held responsible for ............ [More copy to come

as per existing (?) warranty .......... etc. More copy to come as per existing (?) warranty ........

More copy to come as per existing (?) warranty]

(DOCUMENTATION Continued)

LISTINGS

The HD KAP Series Air Purifier Unit is certified by the following listing authorities:

WARRANTY

Commercial Kitchen Ventilation Products

FACTORY SERVICE

Hood Depot’s highly qualified service department personnel are ready to answer any question

and quickly resolve any problem with your KAP unit. Call 24/7 at:

1-800 322-8730

Your One-Stop Source for Kitchen Ventilation

Pg. 17

710 S. Powerline Road, Deerfield Beach, FL 33442 • 954 570-4083 • 800 322-8730 • www.hooddepot.net

Summary of Contents for KAP Series


















Search results

Summary of Contents for KAP Series

Reviews:

Related manuals for KAP Series

Brands by name

Popular brands

Hood Depot KAP Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for KAP Series

Reviews:

Related manuals for KAP Series

Brands by name

Popular brands