background image

13

69-1353

INDOOR HUMIDITY

You will hear, “To hear the indoor humidity, press 6.”

If your thermostat or system has the capability to sense 
the indoor humidity, the Telephone Access Module 
announces the indoor humidity; for example, “The 
indoor humidity is  (__ percent).” After indicating the 
indoor humidity, the Telephone Access Module returns 
to the beginning of the menu.

Receiving Dial-Out Alert Messages

You will hear,”Hello, this is a Honeywell alert message 
from (your ID here). A (alert message) was observed”.

The Telephone Access Module dials the telephone 
numbers from the Telephone Number Setting Menu; see 
Dial-out Telephone Number Settings description in 
Configuring Your Telephone Access Module section for 
further information on entering phone numbers. See 
Table 1 for the alerts that activate a dial-out procedure.

ACKNOWLEDGING DIAL-OUT ALERT MESSAGES

If you (or your designate) receive a dial-out alert 
message, you can choose to acknowledge the message 
and take immediate and appropriate action. 

You will hear, “To acknowledge the alert message, press 
1.”

“To repeat the alert message, press 2.”

“To exit, press the * key.”

If you press the * key to exit and 
the Telephone Access does not 
announce “Goodbye,” there is  
another alert present. Stay on the 
line. If you hang up before 
acknowledging the alerts, the 
Telephone Access Module  
repeats the dial-out procedure.

If an acknowledgement is not received, the 
Telephone Access Module continues calling 
every 30 minutes until an acknowledgement is 
received.

If the Telephone Access Module left a 
message on an answering machine or voice 
mail, call into the Telephone Access Module to 
acknowledge the alert and cancel the dial-out 
alerts. 

If telephone number setting #3 is program-
med, the designate for that number must also 
acknowledge the alert separately with the 
special code to clear the alert.

NOTE:

The special code is the last five digits of the 
telephone number programmed in telephone 
number setting three; see Programming Dial-
Out Telephone Number section.

CAUTION

Property Loss Hazard.
Prepare to act promptly; time may be 
critical. 
Do not assume your designate received and 
acted on the active alert.

80

90

70

60

90

80

70

60

Summary of Contents for W8735B





























Reviews: