manualshive.com logo in svg

Honeywell TRS-3300, Installation And Operating Instructions Manual, Page: 55 / 60

Share
Download
Honeywell TRS-3300 Installation And Operating Instructions Manual Download Page 55

Installation and Operating Instructions TRS 33xx

55

9. FCC 

Statements

The device can contain the transmitter modules:

á

 reader module IC:6587A-X0400600 / FCC ID: UA2X0400600

á

 mifare reader module IC:6587A-X0402100 / FCC ID: UA2X0402100

9.1

Statement required by 15.19 and RSS-210

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. 

Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that may cause
undesired operation.

9.2

Statement required by 15.21

Warning:

Changes or modifications made to this equipment not expressly approved by
Honeywell may void the FCC authorization to operate this equipment.

9.3

Statement required by 15.105

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

á

Reorient or relocate the receiving antenna.

á

Increase the separation between the equipment and receiver.

á

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

á

Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for TRS-3300





























































Reviews:

No comments