manualshive.com logo in svg

Honeywell TRS-3300, Installation And Operating Instructions Manual, Page: 53 / 60

Share
Download
Honeywell TRS-3300 Installation And Operating Instructions Manual Download Page 53

Installation and Operating Instructions TRS 33xx

53

14 = Fuse FS 1

Internal protection, values see chapter 11 = technical data.

15 = Fuse FS 2

Protection of external connections (reader, U

ext

, module bus), values see chapter 11 = technical data.

16 = Plug PL 8 for plug-in connector of foil keypad (3 pole)

The foil keypad has a 10 pole and a 3 pole (see 6) contact tounge.
The 10 pole contact tounge is to be put in the plug SK4 and barred. In ex-works condition this connection does
already exist.

Caution! There is a voltage of approximaltely 100 V AC at the plug-in connector!

This connection is used to realize the backgroung illumination.

Assignment (PIN)

Designation

1

approx. 100 V AC

2

Free

3

0  V

17 = Input voltage (3 pole)

Assignment (PIN)

Designation

Comment

1

U

DC

Power supply input for direct current voltage

(see technical data)

no output

2

0  V

3

 Ground

Summary of Contents for TRS-3300





























































Reviews:

No comments