manualshive.com logo in svg

Honeywell Silent knight 5895XL, Installation And Operation Manual, Page: 31 / 48

Share
Download
Honeywell Silent knight 5895XL Installation And Operation Manual Download Page 31

30

5895XL Manual - P/N 151142-L8:L  08/09/2017

Compatible Devices

Notification Appliances

Appendix A: Compatible Devices

A.1  Notification Appliances

For proper operation, you must use polarized devices with a Model 7628 4.7k ohm EOL resistor on each loop. All supervised notifica-
tion appliances used with the 5895XL must be polarized.

NOTE:

Not all devices can use the Sync feature, be sure to check below table to ensure the device you have chosen will work with this 

feature. This control is UL listed for panel wide Synchronization.

Compatible Devices table below lists notification appliances compatible with the fire alarm control panel. Appliances 
which can be synchronized indicate the type of sync available in the columns marked Audio and/or Visual

.

Manufacturer

Model

Audio

Visual

Type

AMSECO

SH24W-153075

x

x

Horn/Strobe

SAD24-153075

x

Strobe

SAD24-75110

x

Strobe

SL24W-75110

x

Strobe

SL24C-3075110

x

Strobe

SLB24-75

x

Strobe

RSD24-153075

x

Strobe

RSD24-75110

x

Strobe

SH24W-75110

x

x

Horn/Strobe

SH24W-3075110

x

x

Horn/Strobe

SHB24-75

x

x

Horn/Strobe

SCM24W-153075

x

Chimes/Strobe

SCM24W-75110

x

Chimes/Strobe

SCM24C-3075110

x

Chimes/Strobe

SCM24C-177

x

Chimes/Strobe

H24W

x

Horn

H24R

x

Horn

FCI

S2415-FC

x

Strobe

S241575-FC

x

Strobe

S2430-FC

x

Strobe

130-3117C

x

Mini Horn

130-3147C

x

Mini Horn

BLV-6

x

Vibrating Bell

BLV-10

x

Vibrating Bell

BLVCH

x

Vibrating Chime

H12/24-FC

x

Horn

H12/24W-FC

x

Horn

H12/24K-FC

x

Horn

Summary of Contents for Silent knight 5895XL

















































Reviews:

No comments