Honeywell Silent knight 5895XL Installation And Operation Manual Download Page 16

Page: 16 / 48

5895XL Manual - P/N 151142-L8:L 08/09/2017

Calculating Current Draw and Standby Battery

Before You Begin Installing

SD500-ANM

Aux. Pwr

Standby: 8 mA

Alarm: 60 mA

SLC

Standby/Alarm: .55 mA

SD500-SDM

SLC

Standby/Alarm: .55 mA

Aux. Pwr

Standby: 20 mA

Alarm: 106 mA

SLC Accessory Bases

SD505-6RB

Standby/Alarm: .082 mA

SD505-6SB

Aux. Pwr

Standby: 1 mA

Alarm: 32 mA

SLC

Standby/Alarm .082 mA

SD505-DUCTR

Aux. Pwr

Standby: 20 mA

Alarm: 62 mA

SLC

Standby/Alarm: .5 mA

SD505-DTS-K

None, included with SD505-DUCTR worst case.

SD505-DUCT

None, included with detector current.

SLC Isolator Devices

SD500-LIM

(100 max/loop)

Standby/Alarm .092 mA

SD505-6IB

Accessories Modules

5815XL SLC Loop Expander

(63 max.)

Standby/Alarm: 55 mA

6860 Remote LCD Annunciator.

(16 max.)

Standby: 25 mA

Alarm: 50 mA

5860 Remote LCD Annunciator.

Standby: 20 mA

Alarm: 25 mA

6855 Remote LCD Annunciator

Standby: 20 mA

Alarm: 25 mA

5824 Serial/Parallel Printer Interface

(4 max.)

Standby/Alarm: 45 mA

5895XL Power Supply

(16 max.)

Standby/Alarm: 10 mA

5496 NAC Expander

Standby/Alarm: 10 mA

5865-4 LED Annunciator Module
(with reset and silence switches)

(8 max.)

Standby: 35 mA

Alarm: 145 mA

5865-3 LED Annunciator Module

Standby: 35 mA

Alarm: 145 mA

5880 LED I/O Module

Standby: 35 mA

Alarm: 200 mA

5883 Relay Interface

(32 max.)

Standby: 0 mA

Alarm: 220 mA
(22 mA per relay)

EVS-50W or EVS-125W Audio Amplifier
with/without EVS-CE4

(4 max.)

Standby: 10 mA

Alarm: 10 mA

EVS-INT50W Internal Amplifier

(4 max.)

Standby: 52 mA

Alarm @ 25V: 275 mA

Alarm @ 70V: 310 mA

EVS-VCM Voice Control Module

(1max.)

Standby: 70 mA

Alarm: 100 mA

EVS-SW24 Switch Expander

(5 max.)

Standby: 10 mA

Alarm: 25 mA

Table 2.5 Current Draw Worksheet for SD SLC Devices

Device

# of Devices

Current per Device

Standby

Current

Alarm

Current

Summary of Contents for Silent knight 5895XL

















































Search results

Summary of Contents for Silent knight 5895XL

Reviews:

Honeywell Silent knight 5895XL, Installation And Operation Manual, Page: 16 / 48

Search results

Summary of Contents for Silent knight 5895XL

Reviews: