manualshive.com logo in svg

Honeywell Silent knight 5895XL, Installation And Operation Manual, Page: 18 / 48

Share
Download
Honeywell Silent knight 5895XL Installation And Operation Manual Download Page 18

5895XL Manual - P/N 151142-L8:L  08/09/2017

15

Wiring Specifications

Before You Begin Installing

2.7  Wiring Specifications

2.7.1  Length Limitations

This section contains information on calculating SBUS wire distances and the types of wiring configurations (Class A and B).

2.7.2  Calculating Wiring distance for SBUS modules

The following instructions will guide you in determining the type of wire and the maximum wiring distance that can be used with SBUS 
accessory modules.

To calculate the wire gauge that must be used to connect SBUS modules to the panel, it is necessary to calculate the total worst case cur-
rent draw for all modules on a single 4-conductor bus. The total worst case current draw is calculated by adding the individual worst case 
currents for each module. The individual worst case values are shown in the table below.  

* All devices must use the same SBUS and VBUS.

** When doing wire calculations, use .080 amps per device with .105 amps for the last device.

After calculating the total worst case current draw, Table 2.6 specifies the maximum distance the modules can be located from the panel 
on a single wire run. The table insures 6.0 volts of line drop maximum. In general, the wire length is limited by resistance, but for heavier 
wire gauges, capacitance is the limiting factor.

NOTE:

Total worst case current draw on a single SBUS cannot exceed 1 amp. If a large number of accessory modules are required, and the 

worst case current draw will exceed the 1 amp limit, then the current draw must be distributed using 5895XL Power Expanders. Each 5895XL 
Power Expander provides an additional SBUS, with an additional 1 amp of SBUS current. Wiring distance calculations are done separately for 
each 5895XL, and separately for the panel itself.

Model Number

Worst Case Current Draw

6860, 5860, 6855 Fire Annunciator

.120 amps

5815XL SLC Loop Expander

.150 amps

6815 SLC Loop Expander

.078 amps

5824 Serial/Parallel Printer Interface Module

.040 amps

5880 LED I/O Module

.250 amps

5865 LED Annunciator

.200 amps

5895XL Intelligent Power Supply

.010 amps

5496 Intelligent Power Supply

.010 amps

EVS-50W

.010 amps

EVS-125W

.010 amps

EVS-100W

.010 amps

EVS-100W with EVS-100WBU

.010 amps

EVS-VCM / EVS-VCM with EVS-SW24*   **

.080 amps / .105 amps

EVS-LOC / EVS-LOC with EVS-SW24*    **

.080 amps / .105 amps

SK-NIC Network Interface Card

.021 amps

CELL-MOD/CELL-CAB-SK

.145 amps

SK-F485C Fiber Converter

.125 amps

Summary of Contents for Silent knight 5895XL

















































Reviews:

No comments