background image

74-3450—2

8

NOTES:

Level 3 has the highest privilege while level 1 has 

the lowest privilege. 

Initial settings for all passwords are 0 0 0 0.

Time

Use this screen to view or change the date and time. Press-

ing Apply saves the modified settings.

Main—>Settings—>Time

ROOFTOP UNITS (RTU)

Main—>BuildngVw—>RTU Data

The RapidZone Command Display provides access to equip-

ment data via the RTU Data screen. The list below contains 

brief descriptions of the data available.

Duct Static Pressure

: displays duct static pressure.

Control sensor

: displays duct static pressure

Control Setting

: displays static pressure setpoint (see 

IMPORTANT

 below)

EPID Output

: displays bypass damper position as a 

percent open

Cooling Stages

: displays the number of cooling stages that 

are commanded on

Econ Mixed Air

: displays mixed air temperature

Control sensor

: displays mixed air temperature

Control Setting

: displays mixed air setpoint (see

 

IMPORTANT

 below)

EPID Output

: displays economizer damper position as a 

percent open

Fan Command

: displays the fan control output state

Heating Stages

: displays the number of heating stages that 

are commanded on

Mod Cooling

: displays cooling valve position as a percent 

open

Mod Heating

: displays heating valve position as a percent 

open

M18584

Time

Sept/7/2000
Month Day Year
9 : 40 : 12AM
Hour min sec

!!

+

-

Apply

Cancel

M18583

Rooftop Unit Data

Cooling Stages
Duct Static Press
Econ Mixed Air
Fan Command
Heating Stages
RTU Controller

!!

Schedule

-

Page Up

Page Down

1
2.3686 INW
57.3 DF
On
0
52.6 DF

Summary of Contents for S7760A













Reviews: