Honeywell PRIMUS 1000 Pilot'S Manual Download

Page: 178 / 334

PRIMUS

1000 Integrated Avionics System

A28--1146--112--00

6-5

Flight Guidance System (FGS)

Remote Autopilot Switches and Annunciators

Pitch Wheel and Turn Knob Controls

-- Refer to the autopilot

controller section (page 6--6), for a description of the PITCH wheel

and TURN knob controls.

AP Disconnect Switch

-- The AP disconnect switch is mounted on

the control wheel. When pushed, it disconnects the autopilot and

yaw damper.

TCS Button

-- The TCS button is mounted on the control wheel.

When pushed, the pilot can change aircraft attitude, altitude,

airspeed, and/or vertical speed, without permanently disengaging

the autopilot.

GA (Go--Around) Button

-- The go--around button is located on the

throttle. Under normal conditions, if the autopilot is engaged, it

remains engaged and the AFCS commands coupled go--around

minimum speed hold function for the command bars. If only the flight

director is available, a fixed pitch of 8

nose--up is commanded.

Autopilot Power--Up Test

When the autopilot is powered up, it performs a self--test on the servo

circuits, and the autopilot control and disconnect paths.

FGS Caution and Advisory Messages

The engine instrument and crew alerting system (EICAS) displays

messages that relate to the FGS. Table 6--2 contains the red warning

FGS messages that are shown on the EICAS. Table 6--3 contains all

the FGS amber caution messages.

Message

Description

AUTOPILOT FAIL

Autopilot has disengaged and

indicates failed.

PIT TRIM 1 INOP

Main pitch trim is inoperative.

PIT TRIM 2 INOP

Backup pitch trim is inoperative.

Red (Warning) Flight Guidance System Messages

Table 6--2

Summary of Contents for PRIMUS 1000















































































































































































































































































































































Search results

Summary of Contents for PRIMUS 1000

Reviews:

Related manuals for PRIMUS 1000

Brands by name

Popular brands

Honeywell PRIMUS 1000, Pilot'S Manual

Search results

Summary of Contents for PRIMUS 1000

Reviews:

Related manuals for PRIMUS 1000

Brands by name

Popular brands