manualshive.com logo in svg

Honeywell CDMA-X, Installation And Setup Manual, Page: 21 / 24

Share
Download
Honeywell CDMA-X Installation And Setup Manual Download Page 21

CDMA-X Installation and Setup Guide 

 

– 19 – 

 

[S] 

ECP                  Flt 
                         OK 

Program Mode 

Displays either ECP mode or the zones if 4204 / two-4204 was chosen. 

Flt 

Displays the communicator  fault status. 
OK = Normal, No fault. 
G = No network connectivity over CDMA and fault time has expired. 
g = No network connectivity over CDMA and fault time has NOT yet expired. 

[T] 

Test Msg Sent 
        

Test Alarm 

Sends a Test alarm to AlarmNet.  Functional for a 

registered

 communicator only.  If 

the device is not registered, a message is displayed indicating that the command 

cannot be executed. 

[X] 

Reset CPU Y/N   
       

Reset the communicator. 

Pressing [N] returns to normal mode.  

Pressing [Y] resets the device.  
Note, this resets the CPU and does not affect the programming. 

[Shift] 
[

↑

] 

(UP arrow) 

Registering … 
      

Registration 

Registers a programmed communicator with AlarmNet.  

[

↓

] 

(DN arrow)

 

Enter PIN# 
    

 

Registration with PIN for Replacement Module 

Registers a replacement communicator with AlarmNet, once programmed, using the 

existing PIN #.  

[0] 
 
 

Force Server 

Update? 
Y/N 

 

Force Upload of Configuration File to Server 

Pressing [Y] will force the device to upload its entire configuration file to the server. 
Pressing [N] cancels the operation.  

NOTE:

 If the communicator is not initialized when you enter this command, the 

following screen will be displayed: 

Cannot Upload 

Try Later! _

 

 

Wait for the SIGNAL (green) LED to light, indicating the communicator has 

completed its initialization, and try again.

 

[ENTER] 

Strt Prog Mode? 
Y/N_ 

Enter Program Mode 

Press [Y] to enter program mode; otherwise, press [N]. 

 

 

Central Station Messages 

The following messages are sent to the Central Station by AlarmNet for the conditions listed below.  

NOTE:

 The control 

panel sends its own general code (E353) for a trouble condition. 

 

ECP Mode 

4204 Modes 

Alarm Condition 

Alarm Code 

Restore Code 

Alarm Code 

Restore Code 

Power On / Reset (xx=device address)  E339 C08xx  

 

5551 5555 6 

 

ECP Supervision 

E355 C0000  

R355 C0000  

5555 5515 5 

5555 5535 5 

Communication Path Supervision 

 

R350 C0951 

 

5555 5553 5 

Code Download Begin 

E903 C0803 

 

 

 

Code Download End Successful 

n/a 

R903 C0803 

 

 

Code Download Failed 

E904 C0803 

 

 

 

Test 

5555 5555 9 

 

5555 5555 9  

 

 

 

Summary of Contents for CDMA-X

























Reviews:

No comments